Milwaukee 2625-20 vs 2719-20 Compared: Specs & Prices

Key Takeaways

• The Milwaukee® 2625-20 and 2719-20 are one-handed M18 Hackzall saws that look alike but serve different jobs, with the 2625-20 made for light, occasional cutting and the 2719-20 built for frequent, demanding work.
• Both reach up to 3,000 strokes per minute and run on M18™ batteries, so the real decision comes down to motor type, stroke length, and how hard you plan to push the tool.
• The 2625-20 uses a brushed motor with a 3/4" stroke and a dual gear anti-vibration system, while the 2719-20 adds a POWERSTATE™ brushless motor, a 7/8" stroke, REDLINK PLUS™ intelligence, and a counterbalance system that cuts vibration further.
• The 2719-20 cuts up to 50% faster than competing one-handed saws and runs about $102.99, against roughly $79.99 for the 2625-20, so the upgrade pays off mainly for heavier, repeat use.
• You can compare both Milwaukee® Hackzall models side by side at GenuineTools, where each ships factory-sealed at up to 60% off MSRP.

Milwaukee® 2625-20 vs 2719-20 Hackzall: Specs and Price Overview

The Milwaukee® 2625-20 and 2719-20 are both one-handed M18 Hackzall saws, but they sit at opposite ends of the lineup. The 2625-20 is a brushed-motor saw with a 3/4" stroke, built for light, occasional cuts, while the 2719-20 is the FUEL model with a POWERSTATE™ brushless motor and a 7/8" stroke made for frequent, heavier work. Which one fits depends on how often you cut, how tough the material is, and how much you want to spend.

Reciprocating saws get used in cramped, awkward spots more than almost any other tool, so one-handed control and low vibration matter as much as raw power. That is where these two Hackzall models earn their place.

If you are choosing between them, this guide breaks down the motor, stroke, vibration control, and price so you can match the right saw to your workload.

Two Very Different Tools Wearing the Same M18 Badge

At first glance, the 2625-20 and 2719-20 look almost identical. Both are one-handed Milwaukee® Hackzall saws, both run on the M18 battery system, and both are built for cutting in tight spaces. Despite their similar design, they target very different performance levels.

The 2625-20 Is the Everyday Compact Hackzall

The Milwaukee® 2625-20 is a straightforward, brushed-motor Hackzall built for lighter, occasional cutting tasks. It’s designed for convenience and control in confined areas where a full-size saw can’t easily work. This is the kind of tool you reach for when you need something simple, portable, and dependable for general jobsite or home use.

The 2719-20 Is the Performance-Focused FUEL Version

The Milwaukee® 2719-20 steps up into the FUEL line, bringing a brushless motor that’s built for more demanding, frequent use. It feels more refined under load and is designed for users who rely on their tools day in and day out. It’s the better fit for professionals who want more efficiency and consistency on tougher cutting jobs.

Milwaukee® 2625-20 Specs Breakdown

The 2625-20 is built as a compact, one-handed Hackzall designed for control, comfort, and everyday cutting tasks in tight spaces.

Compact and easy to control, the 2625-20 is built for light, everyday cutting tasks in tight spaces.

Motor Type and Cutting Behavior

The 2625-20 uses a brushed motor system, which is reliable for light-to-medium use and keeps the tool straightforward in design. It’s not built for continuous heavy-duty cutting. Still, it performs well for occasional jobs like remodeling, plumbing cuts, and general site work where ease of use matters more than raw endurance.

Cutting Speed and Stroke Performance

It delivers fast cutting motion with up to 3,000 strokes per minute and a 3/4" stroke length. In practical use, this setup provides solid cutting speed through common materials like wood, metal, and PVC, while still maintaining good control for more precise work in confined areas.

Control, Comfort, and Handling

One of the key strengths of the 2625-20 is its Dual Gear Anti-Vibration System, which helps reduce fatigue and improve stability during cutting. Combined with its one-handed design, it allows better control in awkward positions like overhead cuts or tight wall cavities.

Size, Weight, and Jobsite Convenience

The tool is lightweight and compact, making it easy to maneuver in restricted spaces where larger saws struggle. This design also makes overhead cutting noticeably less tiring during extended use.

Blade System and Usability

The QUIK-LOK™ blade clamp allows fast, tool-free blade changes, supporting both SAWZALL® and HACKZALL® blades. It also works with standard M18™ REDLITHIUM™ battery packs, keeping it fully compatible within the broader Milwaukee® system for users already invested in the platform.

Milwaukee® 2719-20 Specs Breakdown

The 2719-20 sits at the top of Milwaukee®’s one-handed Hackzall lineup, built for speed, control, and durability in demanding cutting applications.

Brushless Motor and Real-World Power Advantage

At the core of the 2719-20 is the POWERSTATE™ brushless motor, designed to maximize cutting efficiency by reducing internal friction and heat loss. Compared to brushed models like the 2625-20, more of the battery’s energy is converted directly into cutting performance. In real use, this means stronger, more consistent cutting power under load and less performance drop-off as the battery drains.

Faster Cutting with Longer Stroke Action

The 2719-20 combines up to 3,000 strokes per minute with a longer 7/8" stroke length, allowing the blade to remove more material with each pass. This translates into noticeably faster cutting, up to 50% faster than competing one-handed reciprocating saws, especially when working through thicker lumber, nail-embedded wood, or tougher demolition materials.

REDLINK PLUS™ Intelligence and Tool Protection

The integrated REDLINK PLUS™ system constantly monitors tool and battery communication to optimize performance and prevent overload. When the saw encounters sudden resistance, it intelligently adjusts output to protect the motor and battery. This improves durability and extends overall tool life under heavy use conditions.

Vibration Control and User Comfort

A dual gear counterbalance mechanism significantly reduces vibration, up to 4x lower than traditional reciprocating saw setups. This results in smoother cut starts, better control, and reduced fatigue during extended use, especially important for overhead or repetitive cutting tasks.

Compact Design with Professional Control

Even with its higher performance, the 2719-20 maintains a compact, one-handed design for working in tight or overhead spaces. A pivoting shoe helps keep steady contact with the work surface, improving cut stability and reducing bounce or “bucking” during operation.

Battery System and Jobsite Efficiency

The tool runs on Milwaukee® M18™ REDLITHIUM™ battery packs, delivering strong runtime and compatibility across 125+ M18 solutions. Combined with advanced electronics and brushless efficiency, the system is designed to deliver more work per charge and longer overall battery life compared to standard platforms.

The 2719-20 FUEL Hackzall is built for more demanding and frequent cutting applications.

Price Difference and What You Actually Get for the Upgrade

The 2625-20 usually sits around $79.99, while the 2719-20 is closer to $102.99.

That extra cost mainly gets you a brushless motor, better performance under load, overload protection, and lower vibration. In real use, it means smoother cutting, better durability, and more consistent performance during longer or tougher jobs.

When the 2625-20 Makes More Sense

The 2625-20 is ideal for light, occasional use, small home projects, basic cuts, or quick fixes. It’s a solid, budget-friendly choice if you don’t need heavy-duty performance.

When the 2719-20 Is Worth It

The 2719-20 is worth the upgrade if you use the tool regularly or on tougher materials. It handles demanding work more smoothly, reduces fatigue, and holds up better over time, making it a stronger long-term investment.

Milwaukee® 2625-20 vs 2719-20 Hackzall: Key Differences & Specs

Match the Hackzall to Your Workload, Then Buy It Right

The choice between the Milwaukee® 2625-20 and 2719-20 comes down to how hard you work the tool. The 2625-20 handles light, occasional cutting at a lower price, while the 2719-20 brings the FUEL brushless motor, longer stroke, and lower vibration that pay off on frequent, demanding jobs.

Once you know which model fits, GenuineTools carries both Milwaukee® Hackzall saws in new, factory-sealed condition at up to 60% off MSRP, with regularly updated stock so you can compare prices and grab the right one in a single place.

Available at GenuineTools, Milwaukee® Hackzall tools deliver reliable M18 cutting performance for both light and heavy-duty use.

Find your Milwaukee® Hackzall at GenuineTools and get the right saw for every cut.

Frequently Asked Questions (FAQs)

Can the Milwaukee 2625-20 and 2719-20 Use the Same Blades?

Yes. Both the 2625-20 and 2719-20 work with standard reciprocating saw blades used across most major brands, so you can swap blades easily without needing any adapters. They handle common wood and metal blades well, and you can simply choose the blade based on the material and type of cut rather than the specific tool.

Does the 2719-20 Run Significantly Longer on a Single Charge Than the 2625-20?

Yes, in real-world use, it generally lasts longer per charge. The difference comes from how efficiently each tool uses power during cutting, especially on tougher materials, with the 2719-20 maintaining performance more consistently, while the 2625-20 is better suited for lighter, shorter tasks.

Is the Milwaukee 2625-20 Being Discontinued in Favor of the 2719-20?

There is no confirmed discontinuation of the 2625-20, and both models are still widely available as they serve different user needs, one focused on basic, affordable use and the other on higher performance and frequent work. Availability can change over time, so it’s always best to check current stock before buying.

Can Either the 2625-20 or the 2719-20 Be Used for Overhead Cutting?

Yes, both are designed for one-handed use, which makes overhead cutting more practical compared to larger saws, allowing better control in tight or overhead spaces. The 2719-20 provides a more comfortable feel during longer overhead use, which can help reduce fatigue over time.

Where Can You Choose Between the Milwaukee 2625-20 and 2719-20?

Both the Milwaukee® 2625-20 and 2719-20 are easy to find, but choosing the right place helps you compare options and value more clearly. At GenuineTools, you can get both models and other M18 tools in one place to pick the right fit for your needs without overpaying.

 

*Note: Pricing and/or product availability mentioned in this post are subject to change. Please check the GenuineTools website for current pricing and stock information before making a purchase.